Top and Btm Tank
-
Solder-on tank set
Top Tank
This tank has a 2" diameter hose connection 7 1/2" from the edge of the tank to the center of the pipe, and a 1 1/4" diameter hole on the top-center for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection 6 3/4" from the edge of the tank to the center of the pipe, and a 1/4" NPT flange for a drain fitting.
Learn More -
Case solder-on tank set
Top Tank
This tank has two 2 1/4" diameter hose connections, a deairation baffle, and a 1 3/4" diameter hole for a fill neck.
Bottom Tank
This tan has a 2 3/4" diameter hose connection, a 1/4" NPT flange for a drain fitting, and a 1418PC plate oil cooler.
Learn More -
Hino solder-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, a 1 1/4" hole on top for a filler neck, and an 18mm flange for a sensor.
Bottom Tank
This tank has a 1 3/4" diameter hose connection, and a 1/4" NPT flange for a drain cock. Learn More -
Motor Home solder-on set
The top tank has two 2 1/4" diameter hose connections separated by a baffle in the center, and a 1/4" NPT flange for an expansion fitting. The bottom tank is blank except for a 1/4" NPT flange for a drain fitting.
The side frames consist of a blank channel and a blank angle. Learn More -
Lift Truck tank set
Top Tank
This tank has a 1" diameter hose connection 2 5/8" from the edge of the tank to the center of the hose connection, a 1" diameter hole in the top center of the tank to accommodate a foreign style filler neck, a keyhole style bracket on each end of the tank, and a pair of 1/4" NC nuts on the fan side of the tank.
Bottom Tank
This tank has two pins @ 7 7/8" centers for mounting, four 1/4" NC nuts (two on the fan side and two on the grill side), and a 1" diameter hose connection 2 7/8" from the edge of the tank to the center of the hose connection (connection angles up on a 90o angle, then points towards the passenger side on a 45o angle).
Learn More -
John Deere solder-on tank set
Top Tank
This tank has a 2" diameter hose connection, a hole for a filler neck, and a 1/2" NPT flange for a sight glass.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange for a drain cock.
Note: this set is to replace an original side by side rad and oil cooler - original tanks measured 14" x 3".
Learn More -
Solder-on tank set
These tanks have a 1" diameter hose connection, and the top tank has a hole for a filler neck.
Learn More -
Cat tank set
Top Tank
This tank has a 2" diameter hose connection, a mounting block on eachend with two 5/16" NC threaded holes, and a hole in the top center ofthe tank for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, a mounting block on each end with two 5/16" threaded holes, a locating pin to position the radiator into the frame, and a 1/4" NPT flange for a drain.
Learn More -
Solder-on tank set
Top Tank
This than has a 3" diameter hose connection, and a 1 3/4" diameter hole for a filler neck.
Bottom Tank
This tank has a 3" diameter hose connection that angles out and up, and a 1/4" NPT flange for a drain cock.
Learn More -
Solder-on tank set
Top Tank
This tank has a 2" diameter hose connection, a 1/4" NPT flange for an expansion fitting, and a 1 3/4" diameter hole in the top center of the tank for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange on the grill side.
Learn More