Solder on Tanks
-
Isuzu solder-on tank set
Top Tank
This tank has a 18mm x 1.5mm flange for a sensor fitting, a stand pipe for a filler neck, a 1 1/2" diameter hose connection, and a hole on each end to attach side frames.
Bottom Tank
This tank has a 1/4" NPT flange for a drain fitting, a 1 1/2" diameter hose connection, and two holes for an oil cooler on the grill side spaced @14 3/8" centers.
Learn More -
Cat solder-on bottom tank
This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange on the grill side.
Learn More -
Hino solder-on tank set
Top Tank
This tank has a 2 1/8" diameter hose connection, a 1 1/4" diameter hole for a filler neck, an 18mm flange for a sensor, and two 5/16" NC threaded holes on each end to attach side frames.
Bottom Tank
This tank has a 2 1/8" diameter hose connection, two 5/16" NC threaded holes on each end to attach side frames, and a 1/4" NPT flange for a drain fitting.
Learn More -
Case solder-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, four 5/16" NC nuts to attach side frames, and a 1/4" NPT flange for an expansion fitting.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1" diameter bypass connection, four 5/16" NC nuts to attach side frames, and a 1/4" NPT flange on the grill side for a drain fitting.
Learn More -
Gen Set solder-on complete set
Top Tank
This tank has a 2 1/2" diameter hose connection, a 1 3/4" diameter hole for a filler neck, and a 1/2" NPT flange.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, and a 1/2" NPT flange.
Side Frames
These frames have four 5/16" NC threaded holes along the back.
Learn More -
Generator solder-on
This tank has a 1/4" NPT flange, and a 2 1/2" diameter hose connection. Learn More -
Solder-on Bottom tank
This tank has a 2 1/4" diameter hose connection, two holes for an oil cooler, and a 1/8" NPT flange for a drain fitting.
Oil cooler is 7 1/8" centers - holes are 1 7/16" dia.
Learn More -
Komatsu solder-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, a 1 3/4" diameter hole on top for a filler neck, a 1/2" NC threaded bung for an isolation grommet to attach to, and a 1/8" NPT flange for an expansion fitting.
Bottom Tank
This tank has a 2" diameter hose connection, a 3/8" NPT flange for a drain fitting, and a 10 plate oil cooler with fittings @ 10" centers (#1010PC).
Learn More -
Solder-on complete set
Inlet Tank
This tank has a 1 1/8" diameter hose connection 1 1/2" from the edge of the tank to the center of the pipe, and two 1/4" NPT couplings for a sensor fitting and a drain fitting.
Outlet Tank
This tank has a 1 1/8" diameter hose connection 1 1/2" from the edge of the tank to the center of the pipe, and a 1 3/8" diameter pipe bent upwards 90o for a filler neck.
Frames
Frames are 24" long, with two 5/16" NC threaded nuts @11" centers.
Bottom frame has an additional two 1/2" NC threaded nuts @14" centers.
Learn More -
Solder-on Bottom Tank
This tank has a 1 1/2" diameter hose connection, and a ten plate oil cooler with 18" centers (1018PC).
Learn More