Miscellaneous
-
This sight glass has a fine thread. It comes supplied with an o-ring.
Shown here with matching flange part #1013 (sold separately).
Learn More -
-
10 Plate - 18" centers - 3/4" NPT fitting.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
12 plate oil cooler with 16" centers between the fittings.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Utility Tank
This tank has a step cut out on the top, and a 1/2" NPT fitting for drainage in the bottom center of the tank. Learn More -
Komatsu oil cooler
This oil cooler goes with Komatsu Loader tank #091307A and #090210A.
14 plates, and the bolt-on type flanges are spaced @ 10".
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
14 plates, 18" between the fittings (center to center). Fittings are 3/4" NPT with threads on the outside and nuts.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Komatsu oil cooler
This oil cooler goes with Komatsu tank #091307A and #090210A.
14 plates, and bolt-on type flanges are spaced @ 18" centers.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
16 plates, 3/4" NPT fittings spaced @ 10" (inside threads only)
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Gasket Tape
This is cork gasket material made by Johnson Manufacturing. 100' roll @ 1/16" thick. Peel and stick on one side.
Learn More