Search results for '10" oil cooler'
-
Thomas Bus solder-on tank set
Top Tank
This tank has a 2" diameter hose connection, a 1 3/8" diameter stand pipe for a filler neck and a 1/2" NPT flange on the grill side, a 1" diameter bypass, and a 1/4" NPT flange.
Bottom Tank
This tank has a 2" diameter hose connection, a 1/4" NPT flange, and a #1018PC oil cooler.
Learn More -
Forklift solder-on tank set
Top Tank
This tank has a stand pipe for a filler neck, two holes for an oil cooler @ 8 3/4" centers, a 1 1/2" diameter hose connection, a keyhole bracket, and a 3/8" NC threaded stud.
Bottom Tank
This tank has a 1 1/2" diameter hose connection, a keyhole bracket, a 3/8" NC threaded stud, and a 1/4" NPT flange for a drain fitting.
Learn More -
Fire Truck bottom tank
This tank has a 3" diameter hose connection, a 1/4" NPT flange for a drain cock, four brackets - each with a slotted hole, and a 14 plate oil cooler with 18" centers (the original oil cooler is a tube and shell type).Note: for this tank, samples must be supplied by the customer.
Learn More -
12 plate oil cooler with 16" centers between the fittings.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Case Loader Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1/4"NPT fitting for a drain cock, a 3/4" diameter bypass hose, and a 14 plate oil cooler with 18" centers and 3/4" NPT fittings (replaces the original 15 plate with metric fittings).
Learn More -
Orion Bus CAC bracket
This charged air cooler bracket is 24 1/2" long and 8" wide. There is a mounting bracket on the back, two 1/4" NC threaded holes along the side, three 1/4" NC threaded holes along the opposite side, and various clearance holes for bolting the bracket to the main rad assembly.
Learn More -
Case Tractor bolt-on tank
This tank has a 2 1/2" diameter hose connection, an 818PC oil cooler to replace the original tube-bundle cooler, a 1/4" NPT flange for a drain fitting, and a mounting bracket on each end.
Learn More -
Blue Bird / Thomas Bus / Freightliner
solder-on tank set
Top Tank
This tank has a 2" diameter hose connection, a mounting boss at each end to attach side frames, a 1/4" NPT flange for an expansion fitting, and three brackets on the grill side.
Bottom Tank
This tank has a 2" diameter hose connection, a 1/4" NPT flange for a drain, and two holes for a 7 plate oil cooler with fittings spaced @ 18" (718PC).
Learn More -
Solder-on Bottom Tank
This tank has a 2" diameter hose connection 2" in from the edge of the tank to the center of the hose connection, a 1010PC (10 plate 10" centers) oil cooler (must be provided by the customer), and a 1/4" NPT drain cock flange on the bottom of the tank. Learn More -
Gen Set solder-on set
Top Tank
This tank has a 2" diameter hose connection, a 1 3/4" diameter hole for a filler neck, two 1/4" NPT flanges, a 1" diameter heater bypass connection, and a deairation baffle.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, and can accomodate a 1418PC oil cooler that would replace the original bundle cooler.
Sample Required Learn More
Recently Viewed Products
My Quote
You have no items in your quote.