Search results for 'VOLVO'
-
Volvo / GM / Mack solder-on tank set Top Tank This tank has a 2 1/2" diameter hose connection, a pair of mounting bosses at each end to attach side frames, four 1/4" NC threaded blocks on the top, four 1/4" NC threaded blocks on the grill side, and a 1/4" NPT flange for an expansion barb. Bottom Tank This tank has 2 1/2" diameter hose connection on right side of tank, the flange is for a drain cock, and there are holes @ 11 1/2" centers to accommodate an oil cooler (to be supplied and installed by the customer). Learn More -
Volvo / Autocar top/bottom tank
This tank has a 2 1/4" diameter hose connection 2 1/2" from the edge of the tank to the center of the pipe, a 1/4" NPT flange for an expansion fitting, and three 5/16" NC threaded nuts under the hose connection instead of bolt holes. Learn More -
AutoCar side frame
Top & bottom flanges each have 11 holes, six drilledclearance for 5/16" bolts and five tapped 5/16" N.C.threads. Top flange extends to 12 1/2" wide withthree more holes drilled clearance for 5/16" bolts.Gusset on top supports overhang with six holesdrilled 7/16" dia. and one hole 3/4" dia. Various otherholes for shroud & brackets etc.NOTE: Frames are not interchangeable. Order left fordriver's side or right for passenger's side or pairs. Learn More -
Volvo / Mack plate oil cooler
This oil cooler has seven plates, and the fittings are spaced 10" apart center to center. Cooler comes supplied with large faced fasteners and rubber O rings that fit into a built-in recess.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Volvo / GM / Mack solder-on tank set
Top Tank
This tank has a 2 1/2" diameter hose connection, a pair of mounting bosses at each end to attach side frames, four 1/4" NC threaded blocks on the top, four 1/4" NC threaded blocks on the grill side, and a 1/4" NPT flange for an expansion barb.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, a pair of mounting bosses at each end to attach side frames, four 1/4" NC threaded blocks on the grill side, a 22mm flange for a quick fill line, and two holes @ 11 1/2" centers to accommodate an oil cooler.
Learn More -
Volvo / GM solder-on tank set
Top Tank
This tank has a 2 1/2" Hose connection (angled upward), a 1/4" NPT flange for an expansion tube, two 5/16" mounting holes to attach side frames, three 5/16" NC threaded blocks to mount the surge tank, and four 1/4" threaded blocks to attach the rubber seal.
Bottom Tank
This tank is the same as the top except the hose connection is at the other end, the flange is for a drain cock, and there are holes @ 11 1/2" centers to accommodate an oil cooler (to be supplied and installed by the customer).
Note: this set can also be referenced as #082407A.
Learn More -
Volvo / GM solder-on tank set
Top Tank
This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange to accommodate a hose barb for venting.
Bottom Tank
This tank has a 2 1/2" diameter hose connection slanting at an angle towards the ground, a 1/4" NPT extended flange for a drain cock, two holes @ 10" centers to accommodate an oil cooler, and four mounting bosses to accommodate 5/16" bolts.
Kit comes with a 1/4" NPT drain cock, a 1/4" NPT 90o elbow, and a 1/4" NPT x 3/8" hose barb.
Note: this kit matches brass kit #9303.
Learn More -
Volvo / GM solder-on tank set
Top Tank
This tank has a 2 1/2" diameter hose connection, and 1/4" NPT flange to accommodate a hose barb for venting.
Bottom Tank
This tank has a 2 1/2" hose connection slanting at an angle towards the ground, a 1/4" NPT flange for a drain cock in the center of a "protection bracket", and four mounting bosses to accommodate 5/16" bolts.
Kit comes with a 1/4" NPT drain cock, a 1/4" NPT 90o elbow, and a 1/4" NPT x 3/8" hose barb.
Note: this kit matches brass kit #9302.
Learn More -
Volvo bolt-on tank (1940)
This tank has two 5/8" NF mounting studs 3" long @ 9 1/2" centers, a bolt-on style flange, and a PTO hole through the center.
SAMPLE REQUIRED
Learn More -
Volvo solder-on side frame
This frame must be ordered either left or right (not interchangeable).
The left has two 1/4" NC threaded holes, and two mounting studs @ 10 1/4" centers. The right has three 1/4" NC threaded holes, and two mounting studs @ 13 1/4" centers.
Learn More