Search results for 'KOMATSU'
-
Komatsu oil cooler
This oil cooler goes with Komatsu tank #091307A and #090210A.
14 plates, and bolt-on type flanges are spaced @ 18" centers.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Komatsu oil cooler
This oil cooler goes with Komatsu Loader tank #091307A and #090210A.
14 plates, and the bolt-on type flanges are spaced @ 10".
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Komatsu solder-on bottom tank
This tank has a bolt-on flange 13 1/2" from the edge of the tank to the center of the hose connection. The flange has two 1/2" NC threaded holes @ 4 1/8" centers.
Learn More -
Komatsu solder-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, 12" in from the edge of the tank to the center of the hose connection, a 3/8" NPT flange on the grill side, a notch on either side of the tank, a 1 3/4" diameter hole for a filler neck on top, and a deflection baffle.
Bottom Tank
This tank has a 2 1/4" diameter hose connection 6" in from the edge of the tank to the center of the hose connection, a 1/4" NPT flange for a drain fitting, a notch on either side of the tank, to accomodate a 16 plate oil cooler with fittings @18" centers.(to be supplied by customer)
Same bottom tank as set #101107A.
Learn More -
Komatsu solder-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, a 3/8" NPT flange on the grill side, a 1 3/4" diameter hole on top for a filler neck, and a notch on either side of the tank. The inside of the tank contains a deflection baffle.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1/4" NPT flange, notches on either side of the tank, and a 10 plate oil cooler with 18" centers. Learn More -
Komatsu Loader solder-on tank
This tank has a bolt on style outlet flange, a 14 plate cooler with 19 1/2" centers, and a 14 plate cooler with 9 1/2" centers.
Note: Note: Please check water flange measurements, as to the centers of the 2 bolt holes, the dia. of the "big" hole and whether it is offset or in the center of the tank widthwise (5") way, there are at least 3 different flanges
Coolers must be provided by the customer.
Learn More -
Komatsu Loader solder-on tank
This tank has a bolt-on style flange on the bottom.
On the engine side there are two oil coolers with bolt-on style flanges - #1410PC (14 plates with fittings @ 10" centers)
#1418PC (14 plates with fittings @ 18" centers)
This tank can be provided as a blank channel, or with your old oil coolers RE/RE into the new tank, or as a new tank with new oil coolers.
Note: Please check water flange measurements, as to the centers of the 2 bolt holes, the dia. of the "big" hole and whether it is offset or in the center of the tank widthwise (5") way, there are at least 3 different flanges
Call for pricing and details.
Learn More -
Komatsu Loader solder-on bottom tank
This tank has a bolt-on style flange on the bottom, a 1" NPT coupling and a 1/2" NPT coupling on the bottom, and a 1" diameter bypass connection on the grill side that angles up at 90o and to the driver's side 45o.
On the engine side there are two oil coolers with bolt-on style flanges - #1410PC (14 plates with fittings @ 10" centers)
#1418PC (14 plates with fittings @ 18" centers)
This tank can be provided as a blank channel, or with your old oil coolers RE/RE into the new tank, or as a new tank with new oil coolers.
Note: Please check water flange measurements, as to the centers of the 2 bolt holes, the dia. of the "big" hole and whether it is offset or in the center of the tank widthwise (5") way, there are at least 3 different flanges
Call for pricing and details.
Learn More -
Komatsu solder-on bottom tank
This tank has a 18 plate oil cooler with fittings @ 19" centers (which must be supplied by the customer), a 2" diameter hose connection, a 1 1/4" diameter bypass hose, a 1/4" NPT flange, a 3/8" NPt flange on the bottom of the tank, an a notch on the side of the tank.
This tank goes with the top tank from #010810C
an 18" center 18 plate oil cooler can be provided, but the 3/4" NPT fittings will require adapters.
Or we can RE/RE your old cooler into the new tank.
Call for pricing and details.
Learn More -
Komatsu Dozer tank set
Top Tank
This tank has a 2" diameter hose connection, a 1/2" NC nut for a lifting lug, and a hole for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, two 1/2" NPT flanges for drain fittings, and a plate cooler to be supplied by the customer.
Note: a 1010PC plate cooler can be provided if necessary but the connections will be 3/4" NPT fittings instead of the bolt-on style flanges of the original. This will necessitate modification of the lines on the vehicle.
Or we can RE/RE your old cooler into the new tank.
Call for pricing and details.
Learn More