Search results for '717'
-
Kenworth / Peterbilt solder-on tank set
Top Tank
This tank has a 2 1/2" diameter hose connection 13" from the edge of the tank to the center of the hose connection, a 1/4" NPT flange for a vent, and two mounting bosses at each end of the tank.
Bottom Tank
This tank has a 2 1/2" diameter hose connection 12 7/8" from the edge of the tank to the center of the hose connection pointing towards the ground, and two mounting bosses at each end of the tank.
This set is supplied with eight 5/16" x 4 1/2" bolts with nuts, and a 90o hose barb for the vent.
Learn More -
Kenworth / Peterbilt solder-on tank set
Top Tank
This tank has a 2 1/2" diameter hose connection 13" from the edge of the tank to the center of the hose connection, a 1/4" NPT flange for a vent, and two mounting bosses at each end of the tank.
Bottom Tank
This tank has a 2 1/2" diameter hose connection 12 7/8" from the edge of the tank to the center of the hose connection pointing towards the ground, and two mounting bosses at each end of the tank.
This set is supplied with eight 5/16" x 4 1/2" bolts with nuts, and a 90o hose barb for the vent.
Note: this tank set matches brass kit #9505.
NOTE: top tank hose connection is 3" from center of hose connection to btm of tank, if yours is 2" please refer to part #2717T, tanks are identical except for height of hc Learn More -
Peterbilt surge tank
This tank has a 1" diameter hose connection, a mounting bracket with three holes, a mounting bracket with two holes, a stand pipe for a fill neck, a 1 1/4" diameter hose connection, two 3/8" diameter overflow tubes, and a trough with a through-hole to accommodate mounting.
Learn More -
Hyster Lift Truck solder-on tank set
These tanks have a 1 1/4" diameter hose connection, a 1/4" NPT flange for a drain/temperature sensor, and four 5/16" NC threaded nuts to attach side-frames.
The outlet tank has a 1" diameter stand-pipe for a filler neck.
Learn More -
Forklift solder-on tank set
Filler Tank
This tank has a 1 3/4" diameter hose connection, holes @ 15 1/4" centers for an oil cooler, a stand pipe for a filler neck (part #1005), a mounting bracket, two clips, and three 5/16" NC threaded nuts to attach side frames.
Outlet Tank
This tank has a 1 3/4" diameter hose connection, a mounting bracket, two clips, two 5/16" NC threaded nuts to attach side frames, and a 1/4" NPT flange for a drain cock. Learn More -
Mitsubishi Fuso solder-on tank set
Top Tank
This tank has a 1 7/8" diameter hose connection, an 18mm flange for a sensor, a filler neck hole in the top of the tank, two threaded block for attaching the side frames, and a 1/4" NC threaded block for attaching a clip for the overflow tube.
Bottom Tank
This tank has a 1 7/8" diameter hose connection, a 1/4" NPT flange for a drain cock on the grill side, and two mounting brackets for attaching the side frames. Learn More -
Sky Lift tank set
Top Tank
This tank has a 1 7/8" diameter hose connection, and two mounting pins @ 10" centers (1" long 1/2" diameter).
Bottom Tank
This tank has a 1 7/8" diameter hose connection, two mounting studs @ 12 3/4" centers, and a PTO cutout in the center of the tank. Learn More -
Cat solder-on tank set
Top Tank
This tank has a 2" diameter hose connection, and a filler neck hole in the top center of the tank.
Bottom Tank
This hole had a 2" diameter hose connection, and a 1/4" NPT flange for a drain cock.
Learn More -
Peterbilt bottom tank
This tank is similar to tank #7172, except that the hose connection is 3" in diameter and on a slight angle from front to back.
Learn More -
Hitachi solder-on tank kit
These tanks have 2 3/8" diameter hose connections, the top tank has a filler neck and the bottom has a 1/4" NPT flange for a drain. Mounting brackets on each end.
Individual tanks #4234 and #4235. Learn More