Search results for 'John Deere'
-
John Deere bolt-on bottom tank
This tank has a 2" diameter hose connection, a 1" NPT coupling, a #1216PC oil cooler that replaces the original 8 tube concentric cooler, a 1/4" NPT flange for a drain fitting, and two mounting blocks with 1/2" NC threaded holes @ 11 3/4" centers.
Learn More -
Case solder-on tank set
These tanks have 2" diameter hose connections. The top tank has a hole for a filler neck and two 5/16" NC threaded holes on each end to attach side frames, and the bottom tank has a 1/4" NPT coupling for a drain fitting and two mounting pins with 1/4" NC threaded holes in the center.
Learn More -
John Deere tank set
Top Tank
This tank has a 1 1/2" diameter hose connection that comes out on an angle, four 5/16" NC threaded nuts to attach side frames, a 1 3/8" diameter hole for a filler neck, a 1 3/8" diameter stand pipe for a filler neck (original tank had a screw-cap filler), three 1/4" NPT flanges for a sensor and expansion fittings, and a small surge tank built into the top.
Bottom Tank
This tank has two holes @ 9 1/2" centers for an oil cooler, a 5/8" bypass hose, a 1 3/4" diameter hose connection, a mounting bar running along the center of the tank, and four 5/16" threaded nuts to attach side frames.
Learn More -
Case solder-on bottom tank
This tank has a 2 1/2" diameter hose connection 2 1/2" from the edge of the tank to the center of the hose connection, and a mounting bracket at each end.
Note: this tank matches with top tank #062207A.
Learn More -
Case Tractor tank
This tank has a 2" diameter hose connection 4 3/4" in from the edge of the tank to the center of the hose connection.
Learn More -
John Deere complete rad set
Top Tank
This tank has a 2 1/4" diameter hose connection, a 1 3/8" diameter hole for a filler neck, and a deflection baffle.
Bottom Tank
This tank has a 2 1/2" diameter hose connection, and a 1/4" NPT flange for a drain cock.
Side Frames
These 47 7/16" long by 5 3/8" wide frames have eight 3/8" NC threaded nuts along the edge of the frame, and four 3/8" NC threaded nuts along the opposite edge.
Learn More -
John Deere solder-on tank set
These tanks have a 1 1/2" diameter hose connection 5 3/4" from the edge of the tank to the center of the hose connection, four mounting pins tapped 5/16" NC @ approx. 18 3/4" centers to attach side frames.
The top tank has a 1 3/8" stand pipe on the top for a filler neck, and the bottom tank has a 1/4" NPT flange for a drain fitting.
Learn More -
Case Loader solder-on bottom tank
This tank has a 3" diameter hose connection, a 1 1/4" diameter hose connection that bends towards the ground at approx. 80o, a 1/4" NPT flange for a drain fitting, a 14 plate oil cooler with 18" centers (#1418PC), and a deflection baffle that partially covers the oil cooler.
Learn More -
Case solder-on top tank
This tank has a 2 1/2" diameter hose connection, a 1/2" NPT flange to accommodate a sight glass, and a pair of mounting brackets (one on each end).
This tank matches with bottom tank #071012A.
Learn More -
John Deere solder-on tank set
Top Tank
This tank has a 2 1/4" diameter hose connection 2" long, and a 1 3/8" diameter hole for a filler neck.
Bottom Tank
This tank has a 2 1/4" diameter hose connection 4" long, and a 1/4" NPT flange for a drain cock.
Note: this is a retrofit, the original tanks were narrower.
Learn More