Top and Btm Tank
-
New Flyer Bus oil cooler tank
This tank has two 2 1/2" diameter hose connections separated by a baffle, a 1/4" NPT flange on the bottom, a 1/4" NPT flange on the side, two 1/4" NPT flanges on the back facing opposite of the hose connections, and two angle brackets that run the length of the tank for mounting purposes.
Learn More -
Bolt-on tank set with washer bars
Top Tank
This tank has a height of 3 1/2". There is a 2" diameter hose connection 3" from the edge of the tank to the center of the hose connection. The hose connection is 3" long. There is a 1 3/8" hole to accommodate a filler neck, 6 1/2" from the edge of the tank.
Bottom Tank
This tank is identical to the top tank, except without the filler neck hole.
Note: This set comes with 4 washer bars 21" long with 12 bolt holes, and 4 washer bars 4 1/4" long with 2 bolt holes.
Learn More -
Arens Fire Truck complete set
Overall height is 21".
This was a restoration job. Samples would need to be supplied by the customer to manufacture this set. Learn More -
Bus tank set
This low profile tank (1 5/8") has a 2 3/4" diameter hose connection 3 1/8" from the edge of the tank to the center of the hose connection, and a 3/8" NPT flange in the hose connection for either a drain or an expansion tube.
Shown here with the matching bottom tank.
Learn More -
Bolt-on tank set
This top tank has an overall height of 5". A 2 1/2" NPT nipple hose connection is on the left side, with a 1/2" NPT coupling for sensor nearby, and a 1/2" NPT sight glass flange. The 2 1/2" studs at each end are 3" long, and the top center of the tank has a truck-sized fill neck hole. Learn More -
Woodchipper tank set
Top Tank
This tank has a 2 1/2" diameter hose connection, two 3/8" NPT flanges, four 1/2" NC threaded holes on each end to attach side frames, and a hole in the top for a filler neck
Bottom Tank
This tank has a 3 1/2" diameter hose connection, four 5/8" NC mounting nuts, two 1/2" NC threaded holes on each end to attach the side frames, and a 3/8" NPT coupling on the hose connection for drainage.
Note: this set comes supplied with four washer bars 10" long with 7 bolt holes, and four washer bars 41 5/8" long with 21 bolt holes.
Learn More -
Bolt-on tank set
Top Tank
This tank has two 1 1/4" NPT couplings facing towards the engine.
Bottom Tank
This tank has two 1 1/4" NPT couplings facing towards the ground.
This set comes with four long washer bars and four short washer bars.
Tanks are made from 3/16" thick #304 stainless steel.
Learn More -
Motor Home bolt-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, a hole in the top center for a filler neck, and two angle brackets on each end to attach side plates.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 3/8" NPT flange for a drain, a 14 plate oil cooler with the fittings spaced @ 18" (1418PC), and two angle brackets at each end to attach side plates.
Note: samples are required to build this set.
Learn More -
Bus tank set
Top Tank
This tank has two 2 1/4" diameter hose connections, two 1/4" NPT flanges for drains, a 3/4" NPT flange for a sight glass, and there is a baffle that runs across the center of the inside of the tank.
Bottom Tank
This is a blank tank.
SAMPLE REQUIRED
Learn More -
Gen Set bolt-on tank set
Top Tank
This tank has a de-airation baffle, a 1 3/4" diameter hole for a filler neck, a 2 1/4" diameter hose connection, a 1" diameter bypass connection, a 1/4" NPT flange, two mounting brackets, and a "hood stop".
Bottom Tank
This tank has two 5/8" NC mounting studs @ 26" centers, and a 2 1/2" diameter hose connection.
Learn More