Top and Btm Tank
-
Peterbilt tank
This tank has a 2 1/2" hose connection that comes out at the bottom of the tank then bends 90o, a 1/4" NPT flange for a drain cock, and a PTO cut-out in the center of the tank.
Note: bolt pattern is the same as a #514 or a #800
Learn More -
-
Cat Excavator Tank Set
Top Tank
This tank has a pair of 4 bolt flanges tapped to 3/8" NC, a filler neck (must be provided by the customer), a 1/8" NPT flange on the top of the tank (for bleeding), and a 5 bolt flange on the top of the tank. The inside of the tank contains a deflection baffle, and there is a pair of "threaded ears" on the top of the tank for mounting purposes.
Bottom Tank
This tank has a single 4 bolt flange with holes tapped to 1/2" NC.
note: sample tanks required Learn More -
Bolt-on tank set
Top Tank
This tank has a two 2 1/2" diameter hose connections, a 1" diameter hose connection, a 1/4" NPT flange, and a 1 3/4" diameter hole in the top center of the tank for a filler neck.
Bottom Tank
This tank has a 3 1/2" diameter hose connection, and four 1/2" diameter holes for mounting - the two inside holes are threaded at 1/2" NC.
Note: for this set, samples must be supplied by the customer.
Learn More -
Gen Set bolt-on tank set
Top Tank
This tank has a de-airation baffle, a 1 3/4" diameter hole for a filler neck, a 2 1/4" diameter hose connection, a 1" diameter bypass connection, a 1/4" NPT flange, two mounting brackets, and a "hood stop".
Bottom Tank
This tank has two 5/8" NC mounting studs @ 26" centers, and a 2 1/2" diameter hose connection.
Learn More -
Bus tank set
Top Tank
This tank has two 2 1/4" diameter hose connections, two 1/4" NPT flanges for drains, a 3/4" NPT flange for a sight glass, and there is a baffle that runs across the center of the inside of the tank.
Bottom Tank
This is a blank tank.
SAMPLE REQUIRED
Learn More -
Motor Home bolt-on tank set
Top Tank
This tank has a 1 3/4" diameter hose connection, a hole in the top center for a filler neck, and two angle brackets on each end to attach side plates.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 3/8" NPT flange for a drain, a 14 plate oil cooler with the fittings spaced @ 18" (1418PC), and two angle brackets at each end to attach side plates.
Note: samples are required to build this set.
Learn More -
Bolt-on tank set
Top Tank
This tank has two 1 1/4" NPT couplings facing towards the engine.
Bottom Tank
This tank has two 1 1/4" NPT couplings facing towards the ground.
This set comes with four long washer bars and four short washer bars.
Tanks are made from 3/16" thick #304 stainless steel.
Learn More -
Woodchipper tank set
Top Tank
This tank has a 2 1/2" diameter hose connection, two 3/8" NPT flanges, four 1/2" NC threaded holes on each end to attach side frames, and a hole in the top for a filler neck
Bottom Tank
This tank has a 3 1/2" diameter hose connection, four 5/8" NC mounting nuts, two 1/2" NC threaded holes on each end to attach the side frames, and a 3/8" NPT coupling on the hose connection for drainage.
Note: this set comes supplied with four washer bars 10" long with 7 bolt holes, and four washer bars 41 5/8" long with 21 bolt holes.
Learn More -
Bolt-on tank set
This top tank has an overall height of 5". A 2 1/2" NPT nipple hose connection is on the left side, with a 1/2" NPT coupling for sensor nearby, and a 1/2" NPT sight glass flange. The 2 1/2" studs at each end are 3" long, and the top center of the tank has a truck-sized fill neck hole. Learn More