Bolt On Tanks
-
New Flyer Bus oil cooler tank
This tank has two 2 1/2" diameter hose connections separated by a baffle, a 1/4" NPT flange on the bottom, a 1/4" NPT flange on the side, two 1/4" NPT flanges on the back facing opposite of the hose connections, and two angle brackets that run the length of the tank for mounting purposes.
Learn More -
Bolt-on tank set with washer bars
Top Tank
This tank has a height of 3 1/2". There is a 2" diameter hose connection 3" from the edge of the tank to the center of the hose connection. The hose connection is 3" long. There is a 1 3/8" hole to accommodate a filler neck, 6 1/2" from the edge of the tank.
Bottom Tank
This tank is identical to the top tank, except without the filler neck hole.
Note: This set comes with 4 washer bars 21" long with 12 bolt holes, and 4 washer bars 4 1/4" long with 2 bolt holes.
Learn More -
Gen Set complete solder-on set
Top Tank
The front side of this tank has a pair of 2 1/4" diameter hose connections, a 1 1/2" diameter hose connection and a pair of 1/4" NPT flanges for vents. The outer ends of the tank have mounting flanges with three 1/2" holes, and the top of the tank has a hole to accommodate a fill neck.
Bottom Tank
This tank has a 3" diameter hose connection and a flange for a drain. The outer ends of the tank have mounting flanges with a pair of 1/2" holes.
Side Frames
These frames are 37" long and have five 3/8" slotted holes up each side for mounting the fan shroud.
Note: this set comes supplied with washer bars.
Learn More -
Prevost Bus side frame
This frame has two 4 bolt flanges with 3/8" NC threaded nuts on the back of the frame for mounting. There are four 5/16" NC threaded holes along the side for mounting the fan and shroud.
Goes with tank #7432.
Pairs with frame #011807C.
Learn More -
Prevost Bus Frame
This frame has four 5/16" NC threaded holes along each side of the frame.
Goes with tank #7432.
Pairs with frame #011807B.
Learn More -
Mack Titan top tank with built-in surge tank
This tank has a 2 1/2" diameter hose connection, a 1 1/4" diameter hole in top for a fill neck, a 1/4" NPT flange on the face of the surge tank, a 3/8" diameter fitting on the face of the surge tank underneath the 1/4" flange, and two 3/4" NPT fittings to accommodate a 1" diameter bypass fitting. This tank is de-airated.
Note: this tank's bolt hole pattern matches tank #679.
Front and bottom views shown here.
Learn More -
Mack Superliner top tank with surge tank
This tank has a 2 1/2" diameter hose connection, a 1 1/4"diameter hole in the top for a filler neck, a 1/4" NPT fitting on the face of the surge tank, a 3/8" NPT fitting underneath the 1/4" fitting, and two 3/4" NPT fittings to accommodate a 1" diameter bypass. This tank is de-airated.
Note: this tank shares the bolt pattern with tank #679.
Front and bottom views shown here.
Learn More -
Mack Titan / Superliner top tank with surge tank
This tank has combined fittings and connections to serve both Titan and Superliner applications. The hose connections are blocked off, so the appropriate hose connection needs to be opened before installing.
Note: this tank shares the bolt pattern with tank #679.
Front and bottom views shown here.
Learn More -
Kenworth top tank
This tank has a 1/4" NPT flange at one end for an expansion pipe, and a 1" NPT fitting on top of the tank for a fast fill line.
Learn More -
Bus bracket
This bracket has seven 5/16" NC threaded holes along the header, and two 3/8" NC threaded holes and two 5/16" NC threaded holes on the bracket side.
Learn More