Top, Btm and Frames
-
Terex solder-on complete set
Top Tank
This tank has a bolt-on style flange connection, two 14mm x 1.5mm fittings, and two threaded bars welded to the top with several 14mm x 1.5 mm & 10mm x 1.5mm threaded mounting holes.
Bottom Tank
This tank has a bolt-on style flange connection, two 14mm x 1.5mm fittings, and two threaded bars welded to the top with several 14mm x 1.5 mm & 10mm x 1.5mm threaded mounting holes.
Sides
One side is a simple channel with several slotted holes along the edge, and the other side is flat to support the core.
Original unit was all aluminum.
Learn More -
John Deere Gator solder-on complete set
These tanks have 1" diameter hose connections, and the top tank has a 1/8" diameter flange for an expansion fitting.
Side frames are 12 3/8" long, 3 5/8" wide, and the distance between the tanks is 10".
Learn More -
Gen Set complete set
Top Tank
This tank has a 2" diameter stand pipe, and a 2" diameter hose connection.
Bottom Tank
This tank has a 2" diameter hose connection that comes out the bottom and angles 90o towards the engine.
Side Frames
Frames are 30" long, with an angle bracket centered along one edge with four slotted holes. Learn More -
International solder-on complete set
Inlet/Outlet Tank
This tank has two 2 1/4" diameter hose connections separated by a baffle down the middle of the tank, a 1/4" NPT coupling on the front, and a 1/4" NPT coupling on one end, and a mounting bracket with two 3/8" slotted holes @ 181/4" centers.
Blank Tank
This tank has a 1/4" NPT coupling on the engine side, and a mounting bracket with tow 3/8" slotted holes @ 18 1/4" centers.
Frames
One frame has three 5/16" NC threaded nuts @ 15" centers, and the other is blank.
Tank header size is the same as tank #061809A.
Learn More -
Gen Set solder-on complete set
Top Tank
This tank has a 2 1/4" diameter hose connection, a 1 3/4" diameter hole for a filler neck, and a 3/8" NPT flange.
Bottom Tank
This tank has a 2 1/4" diameter hose connection, a 1/4" NPT flange for a drain fitting, a 3/8" NPT flange, and a 1" diameter bypass hose connection.
Frames
These frames are 38" long with four 1/2" wide slotted holes along each edge. Learn More -
Porsche solder-on complete set
Top Tank
This tank has a 1 3/4" diameter hose connection, and a 1/4" NPT flange.
Bottom Tank
This tank has a 1 3/4" diameter hose connection, a 1/4" NPT flange, a 22mm fitting for a sensor, and two holes @ 11 1/4" centers for an oil cooler.
Frames
These frames had two 5/16" threaded holes in each.
Learn More -
Gen Set solder-on complete set
These tanks have 2" diameter hose connections. The top tank has a 1 1/4" diameter hole for a filler neck, and the bottom tank has 3/8" NC mounting studs @ 11 3/4" centers.
Side frames have five 3/8" threaded nuts along the back, and three 5/16" NC threaded nuts along the edge.
Learn More -
Stationary Unit solder-on complete set
Top Tank
This tank has a 1 3/4" diameter hose connection, and a 1 7/8" stand pipe for a filler neck.
Bottom Tank
This tank has a 1 3/4" diameter hose connection that comes out the bottom and bends @ 90o, and a 1/4" NPT flange for a drain fitting.
Side Frames
These frames have an angle bracket along the back of the frame with three slotted holes. Learn More -
Stationary Unit solder-on complete set
Top Tank
This tank has a 2" diameter hose connection, a 1/4" NPT flange, and a 1 3/4" diameter hole for a filler neck.
Bottom Tank
This tank has a 2" diameter hose connection, and a 1/4" NPT flange.
Side Frames
These frames have an overall height of 40 1/4".
There are four 3/8" NC threaded nuts along each edge. Learn More