Miscellaneous
-
Gasket Tape
This is cork gasket material made by Johnson Manufacturing. 50' roll @ 1/8" thick. Peel and stick on one side.
Learn More -
18 plates, 18" between the fittings (center to center). Fittings are 3/4" NPT and threaded on the outside with nuts.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Freightliner plate oil cooler
This oil cooler is used with solder-on kits #2006CK and #2007CK.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
6 plates - 18" centers - 3/4" NPT fittings
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Volvo / Mack plate oil cooler
This oil cooler has seven plates, and the fittings are spaced 10" apart center to center. Cooler comes supplied with large faced fasteners and rubber O rings that fit into a built-in recess.
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
7 plate - 18" centers - 3/4" NPT fittings
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
8 plate - 18" centers - 3/4" NPT fittings
Important Information!
The transmission plate oil coolers that Taalman supply are intended for use in systems that operate at 80 PSI to 125 PSI typical operating pressure.
The coolers are leak tested to 300 PSI and are statically burst tested to 1000 PSI.
Please ensure that the intended use of the cooler meets the above requirements. Taalman will NOT be responsible for any damage caused by failure of a cooler that is exposed to anything outside of the above parameters.
Learn More -
Mack mini bolt on tanks and rails HDR: 40 1/2" x 3 1/2" - 64BH, top hose connection is 2", 14 1/4" from end to center, btm is 2 1/2" 15" from end to center, pins are 2 1/2" center to center rails are 29" tall. complete with washer bars These are limited qty and have been discontinued, our solder on version is Taalman #2650CK steel Learn More -
NPT to SAE adapter
This adapter facilitates connecting newer style SAE lines to the traditional style NPT oil coolers.
3/4" NPT to 3/4" SAE 12
Learn More -
Solder on top and btm tanks as per sample Top and btm tanks identical, hose conn. 2 1/2" dia, 1/4" NPT fitting 10 5/8" from right end to center, pins on each end @ 22 5/8" centered. NOTE: these tanks are not stock items, plastic tanks are "in house" that we reproduce in steel and solder dip. Learn More